← More from the workshop
ArduinoStepper motor

28BYJ-48 stepper + ULN2003 with Arduino: wiring, code and common problems

How to wire the 28BYJ-48 stepper to a ULN2003 board and Arduino, AccelStepper code for continuous speed and fixed angles, and why it buzzes but won't turn.

Published

Block diagram of Arduino, ULN2003 and 28BYJ-48 motor

The 28BYJ-48 is the cheapest, most widely available stepper motor, usually sold with a ULN2003 driver board. It is weak and slow, but it runs quietly, has a gearbox built in and runs fine from 5V USB. It drives the channel’s 360° turntable.

Specs worth knowing

Spec Value
Voltage 5V (a 12V version exists, check the label on the back)
Type Unipolar, 5 wires
Gearbox About 1:64
Steps per output revolution About 2048 (full-step) or 4096 (half-step)
Practical top speed About 10–15 rpm
Current About 200–250 mA, fine from a USB port

Because of the gearbox, the output shaft has a little backlash when changing direction. That is fine for a turntable or a clock hand; for precise positioning use a NEMA17.

Wiring

The motor plugs straight into the 5-pin socket on the ULN2003 board (it is keyed, so it cannot go in backwards).

Arduino ULN2003
D8 IN1
D9 IN2
D10 IN3
D11 IN4
5V +
GND −

If you power the motor from a separate 5V supply (recommended for several motors), connect the supply GND to the Arduino GND.

Continuous speed

Install the AccelStepper library (Arduino IDE: Sketch → Include Library → Manage Libraries, search for “AccelStepper”).

#include <AccelStepper.h>

// Order 8, 10, 9, 11 (IN1, IN3, IN2, IN4) is required for the 28BYJ-48
AccelStepper motor(AccelStepper::HALF4WIRE, 8, 10, 9, 11);

void setup() {
  motor.setMaxSpeed(1000);   // steps per second (half-step)
  motor.setSpeed(500);       // positive = clockwise, negative = reverse
}

void loop() {
  motor.runSpeed();          // call constantly, no delay() in loop
}

In half-step mode 4096 steps make one revolution, so 1000 steps per second ≈ 14.6 rpm: close to this motor’s limit.

Turn to an angle and stop

#include <AccelStepper.h>

AccelStepper motor(AccelStepper::HALF4WIRE, 8, 10, 9, 11);
const long STEPS_PER_REV = 4096;

void setup() {
  motor.setMaxSpeed(800);
  motor.setAcceleration(400);              // smooth ramp, no jerk
  motor.moveTo(STEPS_PER_REV / 4);         // turn 90°
}

void loop() {
  if (motor.distanceToGo() == 0) {
    motor.disableOutputs();                // switch coils off to keep it cool
  } else {
    motor.enableOutputs();
    motor.run();
  }
}

Common problems

  • Motor buzzes and vibrates but does not turn: wrong pin order. The declaration must be 8, 10, 9, 11, not 8, 9, 10, 11.
  • Turns but skips steps or stutters: too fast. Lower setMaxSpeed to 600–800 and add setAcceleration.
  • Motor and board get hot while idle: the coils are still powered. Call disableOutputs() when you do not need to hold position.
  • Slower than expected: delay() or heavy Serial.print in loop(). runSpeed()/run() must be called constantly.
  • Using an A4988 with the 5V 28BYJ-48: it will not work. The A4988 drives bipolar motors and needs 8V or more, while the 5V version is unipolar. Use the ULN2003, or move to a NEMA17 if you want an A4988.